Description
SENSORS KIT Makers Space IT Lab Punjab Government eproc.punjab.gov.pk here are list of required products.
| Sr. | Item(s) |
|
Item Details / Specifications | Qty | ||||||||||||||||||||||||||||||||||
| 1 | Small passive buzzer module | KY-006 The Buzzer Module consists of a passive piezoelectric buzzer, it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM. |
1 | |||||||||||||||||||||||||||||||||||
| 2 | Knock sensor module |  |
KY-031 The knock sensor, detects the knocks and the taps. It can work like a switch. The sensor sends data momentarily to the board. To keep the LED on, the button state change codes should be used. So the sensor will work as a switch. |
1 | ||||||||||||||||||||||||||||||||||
| 3 | Vibration switch module |  |
SW-420 The default state of the swith is close Digital output Supply voltage:3.3V-5V On-board indicator LED to show the results On-board LM393 chip Dimension of the board: 3.2cm x 1.4cm |
1 | ||||||||||||||||||||||||||||||||||
| 4 | RGB LED SMD module |
 |
KY-009 RGB Full Color LED SMD Module consists of a 5050 SMD LED, use with limiting resistors to prevent burnout. Compatible with popular electronics platforms like Arduino, Raspberry Pi and ESP8266. |
1 | ||||||||||||||||||||||||||||||||||
| 5 | Infrared Transmitter Module |  |
KY-005 The Infrared Transmitter Module consists of just a 5mm IR LED. It works together with the Compatible with popular electronics platforms like Arduino, Teensy, Raspberry Pi and ESP8266. |
1 | ||||||||||||||||||||||||||||||||||
| 6 | Mercury open optical module |  |
KY-017 This module consists of a mercury switch, a 680Ω resistor and an LED that will light up when tilt is detected. The mercury ball will open/close the circuit when the module is rotated. |
1 | ||||||||||||||||||||||||||||||||||
| 7 | Automatic flashing colorful LED module |    |
KY-034 Voltage range: 3.3V – 5V 5MM 7-colour LED |
1 | ||||||||||||||||||||||||||||||||||
| 8 | Mini magnetic reed modules | KY-021 Arduino magnetic reed switch module Keyes. A reed switch is a magnetic sensor that is normally open and gets closed when exposed to a magnetic field. |
1 | |||||||||||||||||||||||||||||||||||
| 9 | Hall magnetic sensor module | |
KY-003 Hall Magnetic Sensor consists of a 3144EUA-S sensitive Hall-effect switch for high-temperature operation, a 680Ω resistor and a LED. Compatible with popular electronics platforms like Arduino and Raspberry Pi. |
1 | ||||||||||||||||||||||||
| 10 | Rotary encoder module | |
KY-040 With Cap rotary encoder is a rotary input device (as in knob) that provides an indication of how much the knob has been rotated AND what direction it is rotating in. It’s a great device for stepper and servo motor control. You could also use it to control devices like digital potentiometers. |
1 | ||||||||||||||||||||||||
| 11 | Speed Sensor | |
IR Infrared Slotted Optical Speed Measuring Sensor Detection Optocoupler Module | 2 | ||||||||||||||||||||||||
| 12 | Detect the heartbeat module | |
KY-039 This project uses bright infrared (IR) LED and a phototransistor to detect the pulse of the finger, a red LED flashes with each pulse |
1 | ||||||||||||||||||||||||
| 13 | Laser sensor module | |
KY-008 Laser transmitter module consists of 650nm red laser diode head and a resistor. Handle with caution, do not look directly into the laser head. |
1 | ||||||||||||||||||||||||
| 14 | Temperature sensor module | |
KY-001 Temperature Sensor Module consists of a DS18B20 single-bus digital temperature sensor, an LED and a resistor. |
1 | ||||||||||||||||||||||||
| 15 | Flame sensor module | |
KY-026 Flame Sensor Module consist of a 5mm infrared receiver LED, a LM393 dual differential comparator a 3296W trimmer potentiometer, six resistors and two indicator LEDs. The board features an analog and a digital output. |
1 | ||||||||||||||||||||||||
| 16 | XY-axis joystick module |  |
KY-023 Joystick module consists of two 10k potentiometers perpendicularly positioned to control the X and Y axis by changing the resistance when the joystick is moved. A push button is activated when the joystick is pushed down the Z axis. |
1 | ||||||||||||||||||||||||
| 17 | Ethernet Shield |  |
Arduino UNO Ethernet Sheild Operating voltage 5V (supplied from the Arduino Board) Ethernet Controller: W5100 with internal 16K buffer Connection speed: 10/100Mb Connection with Arduino on SPI port IEEE802.3af compliant Low output ripple and noise (100 mVpp) Input voltage range 36V to 57V Overload and short- circuit protection 9V Output High efficiency DC/DC converter: typ 75% @ 50% load 1500V isolation (input to output) |
1
|
||||||||||||||||||||||||
| 18 | GPS Module | |
Standalone GPS receiver 9600 baud (default setting; can be changed) 3.3V Device 3.3V TTL IOs; (FYI, the TX 3.3V ‘high’ state will be sufficient to drive normal 5V microcontroller TTL inputs without additional hardware) Onboard LED which flashes to indicate lock U-blox NEO-6M GPS module Under 1 second time-to-first-fix for hot and aided starts Indoor GPS: -162 dBm tracking sensitivity Anti-jamming technology Support SBAS (WAAS, EGNOS, MSAS, GAGAN) U-blox 6 50 channel positioning engine with over 2 million effective correlators Timepulse 5Hz position update rate Operating temperature range: -40 TO 85°C UART TTL socket EEprom to store settings Mounting Hole: 3mm Module size: 23mm x 30mm Antenna size: 25mm x 25mm Cable Length: 50mm |
1 | ||||||||||||||||||||
| 19 | Node MCU | |
Microcontroller: Tensilica 32-bit RISC CPU Xtensa LX106 Operating Voltage: 3.3V Input Voltage: 7-12V Digital I/O Pins (DIO): 16 Analog Input Pins (ADC): 1 UARTs: 1 SPIs: 1 I2Cs: 1 Flash Memory: 4 MB SRAM: 64 KB Clock Speed: 80 Mhz Wi-Fi: IEEE 802.11 b/g/n: Integrated TR switch, balun, LNA, power amplifier and matching network WEP or WPA/WPA2 authentication, or open networks |
1 | ||||||||||||||||||||
| 20 | Pi CAM | |
Size 25 × 24 × 9 mm Weight: 3g Still resolution: 5 Megapixels Video modes: 1080p30, 720p60 and 640 × 480p60/90 Linux integration: V4L2 driver available Sensor: OmniVision OV5647 Sensor resolution: 2592 × 1944 pixels Sensor image area: 3.76 × 2.74 mm Pixel size: 1.4 µm × 1.4 µm Optical size: 1/4″Full-frame SLR lens equivalent: 35 mm S/N ratio: 36 dB Dynamic range: 67 dB @ 8x gain Sensitivity: 680 mV/lux- sec Dark current: 16 mV/sec @ 60 C Fixed focus: 1 m to infinity Focal ratio (F-Stop):2 .9 |
1 | ||||||||||||||||||||
| 21 | Component Box | |
F240/G235 Double-layer anti-fall activity parts box Size: length 234* width 168* height 62mm Material: transparent PP Features: waterproof, anti-UV, anti-corrosion, internal box detachable |
1 | ||||||||||||||||||||
| No. of Items in Kit | 22 | |||||||||||||||||||||||
Reviews
There are no reviews yet.